The Virtual Loop 2.0 is a Vehicle Presence Sensor for use on Gates and Barriers.
The advanced Distance Measuring Radar reliably detects vehicles of all sizes while ignoring nearly all human movement. Eliminate all the hassles of installing and servicing in-ground loops and give your customer reliable activation and presence for all their gate applications.
Detection method: Microwave (FMCW)
Frequency: Microwave: 24GHz, BLE communication 2.4GHz
Response time: Min. 500msec
Power supply: 12-24VDC
Power consumption: Max 300mA (at 24VDC) with Heater ON; Max 90mA (at 24VDC) when Heater is OFF
Output:
- Spec 1: Non-voltage solid state relay output 30VDC 0.3A or less (resistance load) (N.O./N.C.)
- Spec 2: Non-voltage mechanical relay output 30VDC 1A or less (resistance load) (N.O./N.C.)
- Delay (s): Off/0.5/1/2/3/4
- Hold timer (s): Off/0.5/1/2/3/10/30/60
- Mode: Detection/Pre-detection/Mask
- Type: Holding/Pulse IN/Pulse OUT
- Pulse time duration: 150ms/250ms/500ms/1s
Input:
- Spec: NO/NC contact Non-voltage relay Input, On resistance 100Ω or less, Off resistance 200kΩ or more, internal pull-up voltage: approx. 3.3V
- Mode: Link (OR gate)/Link (AND gate)/Inhibit/Wake
Application: Barrier - Activation, Protection / Slide gate - Activation, Protection / Swing gate - Activation, Protection, Shadow
Detectable vehicle speed: 1.2mph-22mph (2 to 35km/h)
Device setting:
- Detection range: 7ft. to 26ft. (1.5 to 8m) 20 inch (0.5m_ pitch)
- Main sensitivity: Level 1 to 7
- Fine tuning presence: Level 1 to 7
- Close range sensitivity:Level 1 to 7
- Side approach detection: Off/On (2.5s)
- Vibration sensitivity: Off/Low/Middle/High
- Sensitivity boost: Off/Low/Middle/High
- Sensitivity boost timer (s): Off/0.5/1/2/3/4/5/10/20/40
- Relay response time: Level 1 to 4
- Presence detection timer:
- Slide gate cancellation: Off/On
Indicator:
- Standard operation mode
-- Detection operation: Standby: Solid green, Detected: Solid red, Bad environment: Solid purple, Calibration incomplete: Solid blue
-- Wake up: Solid blue for 3 seconds
-- Sensor reset: Completed reset: Blinking blue (fast) for 2 seconds
- Smart phone APP connection mode:
-- Setting detection operation: Standby: Blinking green (slow), Detected: Blinking yellow (slow), Bad environment: Blinking purple (slow), Calibration incomplete: Blinking blue (slow)
-- Area check: Standby: Blinking green (slow), Pre-detected: Blinking yellow (slow), Detected: Blinking red (slow)
-- Calibration: In progress: Blinking blue and green, Error unstable: Blinking red and yellow (fast), Error high reflection: Blinking red and blue (fast), High reflection: Blinking purple (for 10s)
Ambient temperture: –22 to 122°F (-30 to 50°C)
Operating ambient humidity: 95% max (no condensation)
Ambient temperature: -22°F to 122°F (-30°C to 50°C)
Operation humidity: 95% max. (no condensation)
Degree of protection: IP66 / NEMA4
Installed condition: Indoor/Outdoor
Installation height: 20 in. (500mm) from road surface to the bottom of the unit
Sensor angle adjustment: Left and right: +/-96 deg. (3 deg. pitch)
Weight: 21oz. (600g) (Including accessories)
Accessories: 4 pcs attached screws (2 pcs metric coarse thread M4 x 12, 2 pcs tapping screw 4 x 20), Quick Reference Guide